Three-dimensional finite element simulation of fracture propagation in rock specimens with pre-existing fissure(s) under compression and their strength analysis

A FORTRAN program, consistent with the commercially available finite element (FE) code ABAQUS, is developed based on a three-dimensional (3D) linear elastic brittle damage constitutive model with two damage criteria. To consider the heterogeneity of rock, the developed FORTRAN program is used to set the stiffness and strength properties of each element of the FE model following a Weibull distribution function. The reliability of the program is assessed against available experimental results for granite cylindrical specimens with a throughgoing, flat and inclined fissure. The calibration procedure of the material parameters is explained in detail, and it is shown that the compressive to tensile strength ratio can have a substantial influence on the failure response of the specimens. Numerical simulations are conducted for models with different levels of heterogeneity. The results show a smaller load bearing capacity for models with less homogeneity, representing gradual coalescence of fully damaged elements forming throughout the models during loading. The maximum load bearing capacity is studied for various combinations of inclination angles of two centrally aligned, throughgoing and flat fissures of equal length embedded in cylindrical models under uniaxial and multiaxial loading conditions. The key role of the compressive to tensile strength ratio is highlighted by repeating certain simulations with a lower compressive to tensile strength ratio. It is proven that the peak loads of the rock models with sufficiently small compressive to tensile strength ratios containing two throughgoing fissures of equal length are similar, provided that the minimum inclination angles of the models are the same. The results are presented and discussed with respect to the existing experimental findings in the literature, suggesting that the numerical model applied in this study can provide useful insight into the failure behaviour of rock-like materials.     

Effects of the geometry of two‐dimensional fractures on their hydraulic aperture and on the validity of the local cubic law

Flow through rough fractures is investigated numerically in order to assess the validity of the local cubic law for different fracture geometries. Two‐dimensional channels with sinusoidal walls having different geometrical properties defined by the aperture, the amplitude, and the wavelength of the walls' corrugations, the corrugations asymmetry, and the phase shift between the two walls are considered to represent different fracture geometries. First, it is analytically shown that the hydraulic aperture clearly deviates from the mean aperture when the walls' roughness, the phase shift, and/or the asymmetry between the fracture walls are relatively high. The continuity and the Navier–Stokes equations are then solved by means of the finite element method and the numerical solutions compared to the theoretical predictions of the local cubic law. Reynolds numbers ranging from 0.066 to 66.66 are investigated so as to focus more particularly on the effect of flow inertial effects on the validity of the local cubic law. For low Reynolds number, typically less than 15, the local cubic law properly describes the fracture flow, especially when the fracture walls have small corrugation amplitudes. For Reynolds numbers higher than 15, the local cubic law is valid under the conditions that the fracture presents a low aspect ratio, small corrugation amplitudes, and a moderate phase lag between its walls.     

Implementation of a coupled plastic damage distinct lattice spring model for dynamic crack propagation in geomaterials

This paper studies dynamic crack propagation by employing the distinct lattice spring model (DLSM) and 3‐dimensional (3D) printing technique. A damage‐plasticity model was developed and implemented in a 2D DLSM. Applicability of the damage‐plasticity DLSM was verified against analytical elastic solutions and experimental results for crack propagation. As a physical analogy, dynamic fracturing tests were conducted on 3D printed specimens using the split Hopkinson pressure bar. The dynamic stress intensity factors were recorded, and crack paths were captured by a high‐speed camera. A parametric study was conducted to find the influences of the parameters on cracking behaviors, including initial and peak fracture toughness, crack speed, and crack patterns. Finally, selection of parameters for the damage‐plasticity model was determined through the comparison of numerical predictions and the experimentally observed cracking features.     

铜藻(Sargassum horneri)在营养限制胁迫后对NH4-N的超补偿吸收研究

以经济马尾藻铜藻(Sargassum horneri)为研究材料,研究了其在营养限制胁迫后对NH_4-N的超补偿吸收情况。实验分营养限制和恢复营养两个阶段进行,每个阶段均设置饥饿处理组、饱和处理组和正常对照组。铜藻在低营养限制胁迫(饥饿)下培养10天后,恢复营养盐培养3天,分别采用次溴酸盐氧化法和锌镉还原法测定培养液中的NH_4-N和NO_3-N的浓度。本文研究发现,饥饿处理组中铜藻吸收氨氮的速率远高于正常对照组和饱和处理组,在恢复培养第一天时,饥饿处理组对NH_4-N的吸收速率最高为14.94μmol/(g·h),与正常对照组及饱和处理组间差异显著。在恢复培养的后两天,三个处理组中铜藻对NH_4-N的吸收速率差异慢慢变小,直至最后几乎相同。三组对NO_3-N没有表现出较高的吸收,最高仅为6.15μmol/(g·h),结果表明:氮源包括NH_4-N和NO_3-N时,铜藻优先选择吸收NH_4-N。实验后称重测定生长速率:对照组、饥饿处理组和饱和组生长率(SGR)分别为8.48%、8.86%、8.01%,ANOVA方差分析表明,三者存在显著差异(P=0.0320.05),从而证实了铜藻也存在超补偿生长的现象。     

基于圆柱多段拟合的隧道中轴线提取方法研究

提出基于圆柱多段拟合的隧道中轴线提取方法。首先对隧道点云数据进行预处理，并将点云按隧道走向分成不同区段；然后对各区段依据轴线与表面点云法线垂直关系，提取精度较低的中轴线；最后对各区段利用圆柱多段拟合，提取精度较高的中轴线。实验表明，隧道中轴线的提取在一定的采样区间具有较高的稳定性，对直线和弯曲的圆形隧道有良好的适用性，算法可靠，精度较高。     

资源三号和天绘一号卫星影像无控联合平差精度分析

近年来国产卫星传感器类型日益丰富，使用自主可控的国产卫星影像进行生产和研究的需求越来越大，多源国产卫星影像联合平差的精度分析显得尤为重要。本文针对在立体测图生产中，资源三号卫星影像在时相较旧、噪声较大、云覆盖和摄影漏洞等特殊困难的条件下，利用天绘一号卫星影像进行补漏生产的情况，最终分析并验证了两者无控联合平差的可行性和成果精度。     

基于重力测点和段差变化的前郭5.8级震群研究与三维反演

利用东北地区近几年流动重力观测数据，分析前郭5.8级震群周边重力点值的时序变化特征，并基于重力段差变化对东北地区整体和局部重力变化引入能够反映异常显著性程度的指标量G和C值，最后对前郭5.8级震群前的重力场动态变化作三维密度反演。结果表明：1）前郭5.8级震群发震构造两侧的局部重力变化具有较明显的差异性，其变化趋势可作为识别构造活化或解耦运动的标志；2）显著性指标量G和C值能够为地震重力前兆的定量描述提供新思路；3）震前重力变化的反演结果显示地震发生在质量运移的过渡区域，垂向反演结果对本次地震的震源深度有一定的揭示意义。     

气候变化下基于物种与植物耦联机制的小白额雁(Anser erythropus)潜在生境及适宜性研究--以长江流域中下游为例

气候变化和人类活动通过改变物种生境而影响物种多样性。小白额雁是长江流域中下游的一种具有较高生态价值的食草型濒危候鸟,受气候变化和人类活动威胁。本文以小白额雁为代表性物种,定量分析了气候变化对长江流域中下游候鸟潜在生境及适宜性空间分布格局的影响。采用Maxent模型模拟了当前情景和全球环流模型(GCMs)气候场景下小白额雁潜在生境及其适宜性分布。研究结果表明,小白额雁分布特征与其栖息地周边植物分布呈显著相关关系;运用Maxent模型模拟小白额雁六种主要食源植物的分布特征,并将其结果作为环境变量,将显著改善小白额雁潜在生境及其适宜性模型的模拟性能;在两种典型浓度情景(RCP 2.6和RCP8.5)下,2070年小白额雁潜在生境适宜性面积将下降。为应对气候变化对小白额雁的影响,应采取更加合理的管理措施和保护政策,包括调整保护区的大小、形状和用途。     

Bacterial productivity in the Prydz Bay and its adjacent waters,Antarctic

1　IntroductionBacteriaandtheiractivitiesplayanimportantroleintheelementalbiogeochemicalcyclesandenergytransformingintheocean (Zhenetal.1 997) .DortchandPackard(1 989) proposedthatfoodwebsintheeutrophicwatersaredominatedbythebiomassofprimaryproducerswhilefoodwebsintheoligotrophicwatersaredominatedbythebiomassofmicrobes.Heterotrophicbacteriahadbeenshowntoplayanimportantroleinthedecompositionoflarge ,rapidlysinkingorganicparticleswithinandbelowtheeuphot iczone ,andfurthertoaffecttheelementaldyn…     

三维旋转扫描测量平台设计与实现

本设计主要用于360°旋转的三维扫描,实现角度数据的实时获取。设计中采用单片机控制交流伺服电机进行自定的角度、速度与方向的旋转并实时上传时间、角度数据至上位机进行处理,实现了对平台旋转精度的控制与检测,着重研究了该传感器误差源的产生,对实际应用中的误差进行了定量分析,利用偏心改正、4分频等方法减少了误差,提高了参数精度。角度范围为360°,角度分辨率为0.01°。